RME ADI-4 DD

Fabricante: RME
Modelo: ADI-4
Preço: 655,59€
Sem IVA: 533,00€

ADI-4 DD - Conversor 8 canais AES/EBU<> ADAT
Um conversor bidireccional de 8 canais com qualidade, muito eficiente e capaz. Suporte até 96kHz 24-Bits AES/EBU para ADAT (e vice-versa) e supressão activa de jitter, SyncAlign, SyncCheck e SteadyClock entre muitas outras características. 

Multiplas possíbilidades de conversão entre AES (AES-3/SINGLE WIRE/ DOUBLE WIRE), ADAT (simples e S/MUX) e SPDIF Óptico.
Características:
Converte formatos bidireccionalmente entre AES/EBU, ADAT e S/PDIF.
Duas entradas e duas saídas ADAT, entrada e saída S/PDIF óptica, entrada e saída AES/EBU em XLR, entradas e saídas AES/EBU através de conector DB-25, sincronismos via Word Clock (in e out).

A tecnologia Intelligent Clock Control (ICC) mantém como válida a última taxa de amostragem no caso de perda ou corte de sinal à entrada. Diversos ADI-4 DD podem ser utilizados em paralelo, podendo ser sincronizados via Word Clock.


The actual states of incoming and outgoing signals and ongoing operations within the unit are displayed by LEDs in an easily overseeable way. SyncCheck, already found in other RME products, not only shows if an input signal is locked, but also if multiple inputs are in synchronicity. Furthermore RMEs SyncAlign ® technology prevents accidental errors of ± 1 sample misalignment between the AES/EBU inputs. The AES output signal can be set to Professsional or Consumer subcode. Channel 1/2 can optionally be received and output optically (TOSLINK).

Connectivity
•    5 x AES/EBU I/O (1 x XLR, 4 x D-sub)
•    2 x ADAT I/O (optical)
•    1 x SPDIF (optical, instead 2nd ADAT I/O)
•    1 x Word Clock I/O
RME's SteadyClock(TM) technology guarantees an excellent performance in all clock modes. Its highly efficient jitter suppression enables the ADI-4 DD to refresh and clean up any clock signal, and to provide the clock signal as reference clock at the word clock output. Additionally, Intelligent Clock Control (ICC) will maintain the last sample rate detected as valid in case of fault and loss of input signal. The device can be stacked without limit, all devices will be sample synchronous by using word clock. All settings are stored at power-off. 

Features
The device basically consists of two converters: four AES-3 inputs to double ADAT outputs, and double ADAT inputs to four AES-3 outputs. The double ADAT ports enable full 8 channel support, from 32 kHz up to 96 kHz (S/MUX). The unit provides one XLR I/O directly. A DB-25 connector allows for a use of industry standard AES-3 I/O breakout cables. Setting an internal connector easily changes the DB-25 connector to meet the pinout of Tascam (Digidesign), Yamaha and Euphonix cables.

Tech Specs

Input AES/EBU: 1 x XLR, 4 x via DB-25 connector, electrically isolated, highly sensitive input stage (< 0.3 Vpp), SPDIF compatible
Output AES/EBU: 1 x XLR, 4 x via DB-25 connector, transformer balanced, 5 Vpp
SPDIF Optical: Second ADAT port can be switched to serve as SPDIF I/O
Input ADAT® optical 2 x TOSLINK, 24-Bit, Bitclock PLL
Output ADAT® optical: 2 x TOSLINK, 24-Bit
Input word clock: BNC, Signal Adaptation Circuit (functional from 1.2 Vpp input signal)
Output word clock: BNC, low-impedance driver stage, 4 Vpp into 75 Ohms, short-circuit-proof
Sync sources: ADAT optical, AES/EBU, word clock
Varipitch: by input signal or word clock
Sample rates: 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, variable (Sync/word clock)
Sample rate range: AES, word clock: 27 kHz-105 kHz, ADAT 33 kHz - 57 kHz
Jitter: Internal clock < 1 ns, word clock In < 2 ns, ADAT In < 2 ns
Jitter sensitivity: all PLLs operate even at 100 ns Jitter without problems
Jitter suppression: circa 30 dB (2.4 kHz)
Power Supply: Operates with voltages ranging from 7-30V DC oder AC, allowing operation with practically any power source, including batteries
External high-quality switching power supply included, for worldwide operation at 100-240 Volt
Dimensions: 215 x 44 x 100 mm

Cables (not included)

BO25MXLR4M4F3: Digital Breakout Multicore, D-Sub to 4 x XLR-F / 4 x XLR-M, 3 m
BO25MXLR4M4F6: Digital Breakout Multicore, D-Sub to 4 x XLR-F / 4 x XLR-M, 6 m

Accessories

    •    External Power Supply for CardBus (NTCB-EU)

    •    Line Cord for Power supply (NETZ-CB)

    •    Car Cable for CardBus (AUTOK)

    •    Cable for Storage Battery (AKKUK)

Escrever opinião


Nome:


Opinião: Nota: HTML não está traduzido!

Classificação: Mau           Bom

Escreve o código na caixa abaixo:




Top